木纹防火板施工流程底层防潮处理→放线→骨架连接件固定→固定龙骨→底层板装置→装置饰面防火板，若隔断墙内有管线装置则应在封罩面板之前完结。隔断墙上有插座等物件，则应在相应方位设加强垫木。

The construction process of wood grain fireproof board includes bottom moisture-proof treatment → laying out → fixing the skeleton connectors → fixing the keel → bottom board installation → installing decorative fireproof board. If there is a pipeline installation inside the partition wall, it should be completed before sealing the panel. If there are sockets or other objects on the partition wall, reinforced wooden pads should be installed in the corresponding positions.

底层板和饰面防火板的装置底层板防潮处理：为了避免墙面的潮气使夹板发生翘曲，墙面应采取防潮措施。其办法有两种：一种在底层上先做防潮砂浆抹灰，干燥后再涂一道防水涂料如1mm涂膜橡胶；另一种是在墙面比较干燥的情况下，采用护墙面板与墙面之间通气，即在罩面板的上、下留透气孔，保证墙龙骨、饰面板干燥。

The installation of bottom board and decorative fireproof board: In order to prevent moisture on the wall from causing warping of the plywood, moisture-proof measures should be taken on the wall. There are two methods: one is to first apply moisture-proof mortar on the bottom layer, dry it, and then apply a waterproof coating such as 1mm coated rubber; Another method is to use ventilation between the wall panel and the wall when the wall is relatively dry, that is, to leave air holes on the top and bottom of the cover panel to ensure the dryness of the wall keel and decorative panel.

放线：放线前要检查墙面的质量情况，弹出竖筋和横筋的龙骨装钉垂直线和水平线。其墙筋的距离应参照罩面板的长、宽规格尺度确定。 木骨架固定；墙体内预埋木砖或嵌入木楔，或许用射钉枪射钉将竖向墙筋钉入墙面上见下图。

Setting out: Before setting out, the quality of the wall should be checked, and the vertical and horizontal lines of the vertical and horizontal reinforcement keel should be marked. The distance between its wall reinforcement should be determined based on the length and width specifications of the cover panel. Fixed with wooden frame; Embed wooden bricks or wedges into the wall, or use a nail gun to nail the vertical wall reinforcement into the wall, as shown in the following figure.

横竖墙筋的距离按放线钉好 装置夹板底层；龙骨装置完结后，将底层夹板依照龙骨距离并依据底层板的规格进行排板，并用铁钉进行装置固定，要求固定牢固，钉帽要隐入板内不得漏出钉头；要求衬板外表无翘曲、起皮现象，外表平整、清洁，板与板之间缝隙应在竖木筋处。

The distance between the horizontal and vertical wall reinforcement is determined by setting out and nailing the device to the bottom layer of the clamping plate; After the completion of the keel installation, the bottom layer plywood should be arranged according to the distance between the keel and the specifications of the bottom layer board, and fixed with iron nails. The fixation should be firm, and the nail cap should be hidden inside the board without leaking the nail head; The lining board should have no warping or peeling on the surface, be flat and clean, and the gap between the boards should be at the vertical wooden bars.

本文由富美家装饰耐火板提供技术支持，更多的详细精彩内容请点击我们的网站https://www.fumeijia.net，我们将会全心全意为您提供满意的服务。

This article is supported by Fumeijia Decorative Refractory Board. For more detailed and exciting content, please click on our website https://www.fumeijia.net We will wholeheartedly provide you with satisfactory service.