富美家抗倍特板的组成及性能指数

　　Composition and performance index of Fumeijia anti double special board

　　一、抗倍特板组成图解

　　1、 Diagram of the composition of the anti duplication special board

　　富美家抗倍特板的材质主要是由表面透明层、装饰色纸、褐色牛皮纸（经过酚醛树脂处理）层层叠压再经过高温高压制作而成的。

　　The material of Fumeijia anti double special board is mainly composed of a surface transparent layer, decorative colored paper, brown kraft paper (treated with phenolic resin) layer by layer, and then produced by high temperature and high pressure.

　　二、抗倍特板性能指标

　　2、 Performance indicators of anti duplication special board

　　目前抗倍特板（高压热固树脂版）性能测试报告，国内还没有统一的产品标准，现在一般参照美国的NEMA LD-2005\ASTM D638-03\ GB/T17657-1999的方法标准来测试产品性能基本参数。

　　At present, there is no unified product standard in China for the performance testing report of high pressure thermosetting resin plates. Generally, the method standards of NEMA LD-2005/ASTM D638-03/GB/T17657-1999 in the United States are used to test the basic parameters of product performance.

　　材料物理性质    标准           测试方法    样快大小和数量    富美家测试平均值

　　Standard testing methods for physical properties of materials - Sample size and quantity - Fumeijia test average

　　拉伸强度        ASTM D638-03   采用万能试验机拉伸试验      176mm*20mm*8mm5块做成哑铃型装   57.3MPa

　　Tensile strength ASTM D638-03 is tested using a universal testing machine with 5 pieces of 176mm * 20mm * 8mm to make a dumbbell shaped fixture with a tensile strength of 57.3MPa

　　耐香烟灼烧性能  GB/T17657-1999 3种不同品牌的香烟放置10秒钟  230mm*230mm*8mm  5块     3级光泽和棕色斑都是中等程度

　　Resistance to cigarette burning performance GB/T17657-1999: Three different brands of cigarettes placed for 10 seconds, 230mm * 230mm * 8mm, 5 pieces, level 3 gloss and brown spots are moderate

　　耐干热性    NEMA LD3-2005    恒定的温度放置烘箱30分钟取出后观察  230mm*230mm*8mm5块   表面无变化

　　Dry heat resistance NEMA LD3-2005: Place in an oven at a constant temperature for 30 minutes and observe the surface of 5 pieces with dimensions of 230mm * 230mm * 8mm without any changes

　　耐污染性     NEMA LD3-2005   用15种常用试剂取1毫升容量滴在表面放置16小时后用清洗液清洗后观察   230mm*230mm*8mm5块  总污染指数为1

　　Pollution resistance NEMA LD3-2005: Drop 1 milliliter of 15 commonly used reagents onto the surface and leave it for 16 hours. After cleaning with cleaning solution, observe 5 pieces of 230mm * 230mm * 8mm with a total pollution index of 1

　　抗落球冲击性  NEMA LD3-2005   用224g的钢球从2m处落下观察表面如其中有一块有变化即为有变化   230mm*230mm*8mm5块   表面无变化

　　Impact resistance to falling balls NEMA LD3-2005: When a 224g steel ball is dropped from a distance of 2m and observed on the surface, if there is a change in one of the pieces, it is considered a change. If there is a change in 230mm * 230mm * 8mm, there is no change on the surface of the five pieces

　　表面耐磨性    NEMA LD3-2005   放置在磨耗机上用500g的力用砂纸旋转到表面的色纸破坏取3个中的的最低值  100mm*100mm*8mm3块  2000转

　　Surface abrasion resistance NEMA LD3-2005. Place it on an abrasion machine and use 500g of force to rotate it with sandpaper until the colored paper on the surface is damaged. Take the lowest value of 100mm * 100mm * 8mm3 from 3 pieces and rotate them 2000 times

　　耐沸水性      NEMA LD3-2005 100度的沸水煮1个小时看变化是否分层和起鼓，如有一块有变化即为有变化  50mm*50mm*8mm5块    无变化

　　Boiling water resistance NEMA LD3-2005: Boil water at 100 degrees Celsius for 1 hour to see if there is any layering or bulging. If there is a change in one piece, it is a change of 50mm * 50mm * 8mm. If there is no change in five pieces, it is considered a change

　　耐刮性     NEMA LD3-2005     在刮痕仪器金刚石施以4N的力来回100次看表面变化      230mm*230mm*8mm5块    表面无变化

　　Scratch resistance NEMA LD3-2005: Apply 4N force back and forth 100 times on the scratch instrument diamond to observe surface changes of 230mm * 230mm * 8mm. There is no change on the surface of 5 pieces

　　抗弯曲强度 GB/T17657-1999   采用万能试验机试验，跨距为长度是厚度的16倍即为320mm长，50mm宽做折弯试验  50mm*460mm*8mm5块  158MPa

　　Bending strength GB/T17657-1999 is tested using a universal testing machine, with a span of 16 times the length and thickness, which is 320mm in length and 50mm in width. Five pieces of 158MPa are tested for bending, measuring 50mm * 460mm * 8mm

　　握螺钉力    GB/T17657-1999   用拉力仪器，拉拔板材内的自攻螺丝，  230mm*230mm*8mm5块    3731N

　　Gripping force of screws GB/T17657-1999: Using a tensile tester to pull self tapping screws inside the sheet metal, 5 pieces of 230mm * 230mm * 8mm 3731N

　　耐高温性    GB/T17657-1999   放置120度摄氏度下，2小时后观察表面  230mm*230mm*8mm5块   表面无变化

　　High temperature resistance GB/T17657-1999: After being placed at 120 degrees Celsius for 2 hours, observe that there is no change on the surface of 5 pieces measuring 230mm * 230mm * 8mm

　　三、抗倍特板尺寸对照表

　　3、 Comparison Table of Dimensions of Anti duplication Special Plate

　　英尺       mm

　　Foot mm

　　4'*8'      1220*2440mm

　　4'*8'      1220*2440mm

　　4'*10'    1220*3050mm

　　4'*10'    1220*3050mm

　　5'*10'    1525*3050mm

　　5'*10'    1525*3050mm

　　5'*12'    1525*3660mm

　　5'*12'    1525*3660mm

　　6'*12'    1830*3660mm

　　6'*12'    1830*3660mm

　　本文由  富美家抗倍特  友情奉献.更多有关的知识请点击  https://www.fumeijia.net/   真诚的态度.为您提供为全面的服务.更多有关的知识我们将会陆续向大家奉献.敬请期待.

　　This article is contributed by the friendship of Fumeijia Kangbeite For more related knowledge, please click https://www.fumeijia.net/ Sincere attitude To provide you with comprehensive services We will gradually contribute more relevant knowledge to everyone Stay tuned