As the fireproof board is a new industry in recent years, many users do not know much about the use of fireproof board. Today, we will explain the specific methods for the use of fireproof board as partition wall.

运用的具体步骤：

Specific steps of application:

1.防火板材：一般情况下建议用6mm厚度以上的玻镁板作隔墙板。

1. Fireproof board: generally, glass magnesium board with thickness of more than 6mm is recommended as partition board.

2.配件：6mm以上的板材固定在框架龙骨上，要用3.5200mm的沉头螺钉固定，钉头低于板面0.5mm，以便保证饰面平整。

2. Accessories: plates above 6mm shall be fixed on the frame keel with 3.5200mm countersunk screws, and the nail head shall be 0.5mm lower than the plate surface to ensure smooth finish.

3.装置：开端装置时，有必要标好龙骨的准确位置，并作好记号。竖龙骨中xin间隔为450-600mm，墙体的衔接处和门窗两边装置时要装附加龙骨，如墙体高度大于2440mm时，须在板材衔接处加装支撑龙骨。

3. Device: when starting the device, it is necessary to mark the accurate position of the keel and make marks. The Xin interval in the vertical keel is 450-600mm. Additional keels shall be installed at the junction of the wall and the devices on both sides of doors and windows. If the wall height is greater than 2440mm, supporting keels shall be installed at the junction of plates.

4.板距：相临板材之间留缝距4-6mm，板材与地面之间有必要留有5mm的空隙，螺钉装置中xin距为150mm，距板边10mm，间隔板角30mm。

4. Plate spacing: the joint spacing between adjacent plates is 4-6mm. It is necessary to leave a 5mm gap between the plate and the ground. The Xin spacing in the screw device is 150mm, 10mm from the plate edge and 30mm from the spacer plate angle.

5.吊挂：卫生间或厨房间等吊挂重物处，有必要用木板或龙骨加固，以免板材受到破坏。

5. Hanging: where heavy objects are hung in toilets or kitchens, it is necessary to reinforce them with boards or keels to avoid damage to the boards.

6.接缝处理：在装置时板材与板材留有空隙4-6mm，用107胶水或强li胶调匀后用刮刀涂改板材及缝隙处，然后用纸带或风格带粘贴压平。

6. Joint treatment: during the installation, there is a gap of 4-6mm between the plate and the plate, mix it evenly with 107 glue or strong Li glue, correct the plate and the gap with a scraper, and then paste and flatten it with paper tape or style tape.

7.涂料装修：可以用喷涂、刷涂或滚涂，但刷涂时有必要参看涂料的有关说明。

7. Coating decoration: spraying, brushing or rolling can be used, but it is necessary to refer to the relevant instructions of the coating when brushing.

8.装修面贴瓷砖：在浴室、卫生间、厨房、地下室等湿润区域装置时，如需在板面贴瓷砖龙骨之间的间隔有必要缩短到400mm。墙体每隔三块板(约3.6mm左右)有必要留有一条伸缩缝。

8. Tiling the decoration surface: when installing in wet areas such as bathroom, toilet, kitchen and basement, if it is necessary to paste tiles on the board surface, the interval between keels must be shortened to 400mm. It is necessary to reserve an expansion joint every three plates (about 3.6mm) of the wall.

9.隔音墙体：如需墙体有较高的隔音效果，有必要要求墙体和板材结合严密密闭，再向空墙内填充矿棉，如龙骨双面采用两种不同厚度的板时，隔间效果更佳。

9. Sound insulation wall: if the wall is required to have high sound insulation effect, it is necessary to require the combination of wall and plate to be tightly sealed, and then fill the empty wall with mineral wool. If two plates with different thickness are used on both sides of keel, the compartment effect is better.

10.抗冲击墙体：建议您选用8mm以上的防火板或加一层板，di二张板须用长一些的螺丝钉加固。这种办法可增强抗冲击、隔热、隔音效果和防火性能。

10. Impact resistant wall: it is recommended that you select a fireproof board of more than 8mm or add a layer of board, and di two boards must be reinforced with longer screws. This method can enhance impact resistance, heat insulation, sound insulation and fire resistance.