在线咨询
扫一扫

官方微信二维码
扫描加关注

全国免费服务热线
18560211715

返回顶部
新闻动态主页 > 新闻动态

如何打造富美家防火板

1、下料
 
1. Blanking
 
依照施工图纸和现场施工要求,考虑板材的厚度,应依照风管内径下料;弯头、变径、三通等处板材须特别下料。为了避免风管强度的减小,制造时尽量减少风管长度方向的材料拼接(风管底面和顶面能用整板的尽量用整板),需求切开的,应尽量保存风管周围面或短边标准。
 
According to the construction drawings and site construction requirements, considering the thickness of the board, should be in accordance with the air pipe diameter blanking; elbow, diameter change, tee and other parts of the board must be specially blanking. In order to avoid reducing the strength of the duct, the length direction of the duct should be minimized in the manufacture of material splicing (the bottom and top of the duct can use the whole plate as far as possible), the need to cut, should be as far as possible to preserve the duct around the surface or short side standard.
富美家防火板
2、切开
 
2. Cut open
 
板材的切开均在克己加工平台上完毕。在1段风管的同一平面上尽量不拼接板材。
 
The cutting of plates is finished on the self processing platform. Try not to splice the plates on the same plane of the 1 sections.
 
为了行进加工功率,风管下料和切开要成批制造,构成流水线作业,即同一标准的风管平面板材会合加工,以加强各切开后板材的互换性,这样既能够行进材料的利用率,也能够行进施工功率。
 
In order to advance processing power, air duct blanking and cutting should be manufactured in batches, forming a pipeline operation, that is, the same standard air duct planar sheet joining processing, in order to enhance the interchangeability of each cut after the sheet, so as to be able to travel material utilization, but also to travel construction power.
 
其他,板材下料和切开时,要注意板材的正不好,差异办法是:光滑面为正面,较粗糙面(有字面)为不好。
 
Otherwise, when cutting and cutting, we should pay attention to the plate, the difference is: smooth surface is positive, rough surface (literal) is not good.
 
3、固定角龙骨的加工
 
3. Processing of fixed angle keel.
 
在现场,每段风管顶面或底面与周围面的表里拼接缝处用轻钢角龙骨支撑加固,角龙骨与风管选用自攻螺钉固定。轻钢角龙骨也能够用镀锌铁皮制造(铁皮风管的下角料),这样既能够操控本钱,也能够抵达规划的强度和标准的规矩。
 
On the spot, the top or bottom of each section of air duct and the surface of the surrounding joints are strengthened with light steel angle keel support, angle keel and air duct are fixed with self-tapping screws. Light steel horn keels can also be made of galvanized sheet iron (the bottom corner of the sheet iron duct), so that both the cost can be manipulated and the planned strength and standard rules can be met.
 
加工角龙骨前要预留组装板的厚度,注意在2节风管拼接处应对角龙骨长度进行特别操控,以便于风管搭接健壮。操控准则如下:
 
The thickness of the assembly board should be reserved before machining the angle keel. The length of the angle keel should be specially controlled at the joint of the two air ducts so as to make the air duct more robust. The operation criteria are as follows:
 
依据风管强度的不同,其表里都能够加设龙骨。单节风管制造时内龙骨一端要伸出该管段200~300mm,另一端要缩进该管段200~300mm,以便在设备时与另一节风管拼接紧密,并加强拼接强度。而外龙骨恰与内龙骨相反,内龙骨伸出的一端外龙骨应缩进50~100mm,内龙骨缩进的一端外龙骨应伸出50~100mm,相同,这种做法也为了富美家防火板使风管联接紧密,增加强度。
 
According to the strength of the duct, the keel can be added to the inside and outside. One end of the inner keel should extend 200-300 mm and the other end should be retracted 200-300 mm in order to connect tightly with the other one and strengthen the splicing strength. On the contrary, the outer keel should be retracted 50-100 mm at one end and 50-100 mm at the other end. The same is true for Fumei Fire Protection Board to tighten the connection of air ducts and increase the strength.
以上是富美家防火板的打造工艺,更多精彩内容点击:http://www.fumeijia.net
 
The above is the building process of Fu Mei's fire prevention board, and more highlights: http://www.fumeijia.net