对抗倍特板进行加工时需要注意的问题有哪些？抗倍特板材作为高密度的人造板材，质地很坚硬。因此富美家抗倍特板厂家认为，在加工抗倍特板时应注意以下几个方面：

What are the problems that should be paid attention to when processing the anti double plate? As a high-density artificial plate, anti Beite plate has a very hard texture. Therefore, fumeijia anti magnification plate manufacturer believes that the following aspects should be paid attention to when processing anti magnification plate:

1.开料时，需要以直线锯切为主。通常可先在抗倍特板材上画好规格尺寸，然后再锯切。如果工件的尺寸为标准尺寸，可先用模板划线后再进行锯切，这样会更加方便。

1. During cutting, straight sawing is required. Generally, the specification and size can be drawn on the anti magnification plate first, and then sawing. If the size of the workpiece is the standard size, the template can be used for scribing and then sawing, which will be more convenient.

2.开孔时，可以使用手提曲线锯进行切割，切割速度控制在3-4m/min为宜。如果切割速度过快，一方面可能会造成切割边缘爆口等缺陷，另一方面也可能会影响锯条的使用寿命，增加加工的成本。

2. When opening holes, hand-held curve saw can be used for cutting, and the cutting speed should be controlled at 3-4m / min. If the cutting speed is too fast, on the one hand, it may cause defects such as cutting edge explosion, on the other hand, it may affect the service life of the saw blade and increase the processing cost.

3.对异形边沿进行加工时，需要先在板件表面划出所需尺寸，然后使用曲线锯切割；如果是批量生产，可以在模板的辅助下进行切割，这样可同时确保加工速度和锯切质量。

3. When processing the special-shaped edge, the required dimension shall be drawn on the surface of the plate first, and then the curve saw shall be used for cutting; In case of mass production, the cutting can be carried out with the help of the template, which can ensure the processing speed and sawing quality at the same time.

4.加工边缘，通常采用的工具是手提镂铣机。加工之前需要清除板件表面的灰尘或异物，以免在板件表面留下划痕或刻痕。另外镂铣机的加工速度应保持在2m/min为宜。

4. The commonly used tool for edge processing is a hand-held router. Before processing, the dust or foreign matters on the surface of the plate shall be removed to avoid scratches or nicks on the surface of the plate. In addition, the processing speed of the router should be kept at 2m / min.

如果镂铣刀刀刃角度较小而工件厚度又较厚时，镂铣机的加工速度应适当放慢。另外，铣刀刃的长度应该大于加工件的厚度，这样可以保证一次走刀就能铣削出边缘的线型。

If the cutting edge angle of the router is small and the workpiece thickness is thick, the processing speed of the router should be appropriately slowed down. In addition, the length of the milling cutter edge should be greater than the thickness of the workpiece, so as to ensure that the line shape of the edge can be milled in one pass.

走刀时，镂铣刀从高处逐步向低处下滑，直至镂铣刀刃包容铣削边缘。值得注意的是，走刀时，一定要保持平稳，不要让镂铣机晃动。晃动会使工件的边缘形成不规则波纹，给后续的砂磨抛光工序增加工作量，影响加工效率。

When cutting, the router will slide from high to low until the router edge contains the milling edge. It is worth noting that the cutter must be kept stable when walking, and do not let the router shake. Shaking will cause irregular ripples on the edge of the workpiece, increase the workload of the subsequent sanding and polishing process, and affect the processing efficiency.

5.打磨时，应注意不要损坏表面装饰层。打磨结束后，用抛光剂对边缘进行抛光处理。

5. When grinding, be careful not to damage the surface decoration layer. After polishing, polish the edges with polishing agent.

抗倍特板在安装结束时，如果表面出现斑点或污迹，可用毛巾沾取少量油性清洁剂(油与丙酮的混合物)轻轻擦拭去这些斑点或污点。如果没有斑点或污迹，用一般清洁剂如肥皂加水，或洗洁精加水擦拭即可。更多相关内容就来我们网站https://www.fumeijia.net咨询了解吧。

At the end of installation, if there are spots or stains on the surface of the anti magnification plate, use a towel to dip a small amount of oily detergent (mixture of oil and acetone) and gently wipe them off. If there are no spots or stains, use general detergent such as soap and water, or detergent and water to wipe. For more information, please visit our website https://www.fumeijia.net Consult and understand.